Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
In this article in the next paragraph you can get a bunch of excellent details all about Tools You Need to Install a New Bathtub .
Installing a bath tub isn't specifically rocket science, however it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old bathtub is readily obtainable, the job can move speedily; if you need to open a wall to get rid of the old bathtub and place the new tub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will require an assistant to move out the old bathtub and also set in the new one. Make certain you have actually certified yourself for the task and fit trying it. Rather than working with a contractor to take control of a halfway-completed job, it is better to think about using one before you start. Possibilities are you might require an expert plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your shower room if you have already acquired a brand-new tub and do not need to change the setup of your previous water system pipes.
Your devices as well as product checklist should consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome because of the limited accessibility that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Before proceeding to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type should be attached to the tap ends initially, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Utilizing both wooden boards under its feet, position the tub in the required setting. The wood boards are practical in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little points.
The next objective is to make certain that the tub is leveled all round. This can be achieved by examining the level and adjusting the feet on the tub till the level checks out degree.
To set up faucets, fit the bottom of the furthest flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water and also examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bath tub as well as additionally inspect the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been made use of a minimum of when as this will certainly settle it into its final setting.
Preparing for the Setup
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last setting.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and installations. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy more info about Tools You Need to Install a New Bathtub ? Give a remark below. We would be pleased to know your ideas about this posting. Hoping to see you back again soon. Do you know about another individual who is curious about the niche? Be sure share it. Thanks a lot for your time invested reading it.
Overflow? Ring now! Report this page